GE Intelligent Platforms > Support >  Drivers - General > DG95
JYC Johnson-Yokogawa YS 100 Series
File(s)
Type File Name Date Posted Size Description

There are files attached to this record that may require you to login.

 


Description
ProductVersionModule
HMI/SCADA - iFIX All All
Code : JYC
Vendor : GE Intelligent Platforms
Hardware Manufacturer : Johnson-Yokogawa
Notes : Available for use with FIX32 and iFIX only.

General

Platform Latest Version Type
Windows 2000 6.0 COM
Windows 3.1 4.2 COM
Windows 95 6.0 COM
Windows NT 6.0 COM

Supported
Devices

Device Manufacturer Comment
YS150 Single Loop Multi-Function Controller (Series 1 and 2) Johnson-Yokogawa -
YS170 Single Loop Programmable Controller (Series 1 and 2) Johnson-Yokogawa -

Additional
Requirements

Software Manufacturer Vendor Part No. Comment
none

Protocol

Type Supported Baud Rates Data Bits Stop Bits Parity Error Checking Hand Shaking Comment
Multi-Drop Asynchronous, half-duplex, ASCII codes, Yokogawa TTY Procedure, Vertical Parity Error Detection. 1200, 2400, 4800, and 9600 7, 8 1, 2 None, Odd, Even None, RTS/CTS, DTR/DSR, RTS - -

Supported
Data Types

Data Type Comment
none

Supported
Memory Types

Device Memory Type Comment
Cascade Hardware Mode A1, A2, X1, G1, G1A, G2, G2A, G1D, S1, S2, T1, T2, CFG -
Program Hardware Mode (YS170 only) A1, A2, A3, A4, K1, P1, PGM, PP1, T, X1, G1, G1A, G2, G2A, G1D, S1, S2, T1, BS1, T2, BS2, CFG -
Selector Hardware Mode A1, A2, X1, G1, G1A, G2, G2A, G1D, S1, S2, T1, T2, CFG -
Single Hardware Mode A1, X1, G1, G1A, G1D, S1, T1, CFG -

Commands

Device Command Description Uses
All Devices DG Data Read Command: for reading data from YS100 Series controllers. -
All Devices DP Data Write Command: for setting YS100 Series controllers. -
All Devices WDT Supervisory Computer Watchdog Timer Setting Command in DDC and SPC modes: for initial setting and maintaining of the YS100 Series supervisory computer watchdog timer. -

Signal
Conditionings

Signal Type Description Comment Typical Gain Convergance Range
EGU Scales parameter value to SCLx, SCHx, and SCDPx of appropriate loop. Since the range low limit, range high limit, and depth are gathered within data group CFG, and if this group is not configured within a poll record for the device, no scaling will be performed. - -
NONE Returns raw value No alarming on out of range. - -

Miscellaneous
Info

Relevant Notes
none

History

Revision History
Reason for 6.00 Release on 4/8/96:
* Driver released including all previous SIMs.

Reason for 6.00a Release on 9/25/98:
* Corrected problem of driver transmitting even if NONE was
selected as the primary COM port.

Reason for 6.00b Release on 10/30/00:
* Corrected a problem with the driver rejecting certain I/O
addresses entered for second channel.

Reason for 6.00c Release on 10/03/03:
* Corrected problem with poll task hanging when there was noise on the serial connection.

Reason for 6.00d Release on 6/9/2005:
* Driver has been rebranded to reflect GE Fanuc.


Details
ID: DG95
Category: I/O Drivers
Last Updated: 03/29/10
Date Created: 04/24/00
Status: Published
Attachments: Yes
Language: English


 


Feedback

The feedback portlet allows users to rate content and share these cumulative ratings with other users.
Rate this content record (1=lowest, 5=highest)
5
4
3
2
1
Comment


Note:  If your firewall blocks ZIPS and EXEs, simply right-click and select SAVE TARGET AS and change the extension to something like "XIP".  Once downloaded change the extension back to its original one.

All drivers produced by vendors other than GE ("3rd Party Drivers") are provided by GE "as is" and without warranty of any kind unless the vendor extends a pass-through warranty to the end user.  Support for 3rd Party Drivers is provided by the driver's vendor.