| Type |
File Name |
Date Posted |
Size |
Description |
There are files attached to this record that may require you to login. |
| Product | Version | Module | | HMI/SCADA - iFIX |
All |
All |
Code : GES
Hardware Manufacturer : GE Intelligent Platforms
General
| Platform |
Latest Version |
Type |
| Windows NT, 2000, XP, Server 2003 |
1.3.1.0 |
NET |
Supported
Devices
| Device |
Manufacturer |
Comment |
| GE PAC Systems RX3i PLC |
GE Fanuc |
IC698CPU310 |
| GE PAC Systems RX7i PLC |
GE Fanuc |
IC698CPE010, IC698CPE020 |
| GE Series 90-30 PLC |
GE Fanuc |
IC693CMM321 |
| GE Series 90-70 PLC |
GE Fanuc |
IC697CMM742, IC697CMM741 |
| Versamax |
GE Fanuc |
IC200CPUE05, IC200SET001 |
Additional
Requirements
| Software |
Manufacturer |
Vendor |
Part No. |
Comment |
| none |
Protocol
| Type |
Supported |
Baud Rates |
Data Bits |
Stop Bits |
Parity |
Error Checking |
Hand Shaking |
Comment |
| none |
Supported
Data Types
| Data Type |
Comment |
| INT |
2 Byte Signed Short Integer |
| REAL |
4 Byte Floating Point |
| DINT |
4 Byte Signed Integer |
| SINT |
1 Byte Signed Character |
| UINT |
2 Byte Unsigned Short Integer |
| USINT |
1 Byte Unsigned Character |
Supported
Memory Types
| Device |
Memory Type |
Comment |
| |
%I |
Discrete Input |
| |
%T |
Discrete Temporary |
| |
%SA, %SB, %SC |
Discrete system status |
| |
%G |
Global Reference Data |
| |
%AQ |
Analog Output |
| |
%W |
W table word (PAC Systems RX7i and RX3i only) |
| |
%Q |
Discrete Output |
| |
%M |
Discrete Internal |
| |
%S |
Discrete S system status (read-only) |
| |
%AI |
Analog Input |
| |
%R |
Register |
Commands
| Device |
Command |
Description |
Uses |
| none |
Signal
Conditionings
| Signal Type |
Description |
Comment |
Typical Gain |
Convergance Range |
| none |
History
| Revision History |
Reason for 1.0 release on 9/30/2003:
* New driver.
Reason for 1.1 release on 6/25/2004:
* Added support for PACSystems RX7i v2.0 PLC's for Redudndant IP.
Reason for 1.2 release on 10/15/2004:
* Added support for PACSystems RX3i.
* Added support for Read/Write OPC Strings (BSTR).
* Corrected issue with accessing %W memory above %W65535.
* Corrected issue when installing to a directory with spaces.
Reason for 1.3 release on 07/18/2006:
* Validated server running in Windows XP sp2 and Windows 2003 Server sp1 environments.
* Validated server connecting to a 90-30 CPU374.
* Enhanced communications performance when using Symbolics.
* Enhanced to detect the version of PVT file being used. Will only display published variables when reading from newer version PVT files.
* Documentation has been updated to better describe, array [hints], scaling, browsing, itemID syntax, and removed references to DDE since it is not supported.
Reason for 1.3.1.0 release on 09/16/2008:
* Added support for Diagnostic Logic Block : This change will allow clients of the SRTP driver to access published variables used locally in Diagnostic Logic Blocks. Note: PME Programmer version 5.9 is required to create Diagnostic Logic Blocks. PACSystems Firmware version 5.60 is required to use Diagnostic Logic Blocks. (not yet released as of date of this SIM).
* Added support for LREAL : This change will allow clients of the SRTP driver to access 64-bit floating point (LREAL) values that are stored in analog or non-discrete symbolic memory in the PLC. Symbolic address that refer to LREAL variables are read as LREALs with no special addressing. LREAL data in %R, %W, %AI, %AQ can be accessed using the [LREAL] data type suffix with the address (eg. %R0001 [LREAL]). Note : PME Programmer version 5.8 is required to create LREAL variables. PACSystems Firmware version 5.50 is required to use LREAL variables. |
|
|
Overall Rating: 4
 (2 responses)
Note: If your firewall blocks ZIPS and EXEs, simply right-click and select SAVE TARGET AS and change the extension to something like "XIP". Once downloaded change the extension back to its original one.
All drivers produced by vendors other than GE ("3rd Party Drivers") are provided by GE "as is" and without warranty of any kind unless the vendor extends a pass-through warranty to the end user. Support for 3rd Party Drivers is provided by the driver's vendor.
|
