GE Intelligent Platforms > Support >  Drivers - General > DG270
WIM Westinghouse IMPACC
File(s)
Type File Name Date Posted Size Description

There are files attached to this record that may require you to login.

 


Description
ProductVersionModule
HMI/SCADA - iFIX All All
Code : WIM
Vendor : GE Intelligent Platforms
Hardware Manufacturer : Westinghouse
Notes : Available for use with FIX32 and iFIX only.

General

Platform Latest Version Type
Windows NT 6.03 RES

Supported
Devices

Device Manufacturer Comment
Addressable Relay II Westinghouse -
Advantage Westinghouse -
Advantage Control Module ACM Westinghouse -
Digitrip II RMS T700/800 Westinghouse -
Digitrip III RMS T810 Westinghouse -
Digitrip MV Westinghouse -
Digitrip Optim Westinghouse -
Digitrip RMS T910 Westinghouse -
IQ 1000 Westinghouse -
IQ 1000 II Westinghouse -
IQ 500L Westinghouse -
IQ 502/504 Westinghouse -
IQ Analyzer Westinghouse -
IQ Data Plus Westinghouse -
IQ Data Plus 4000 Westinghouse -
IQ Data Plus II & HV Westinghouse -
IQ Energy Sentinal Westinghouse -
IQ Generator/IQ Data Westinghouse -
IQ Transfer Switch Westinghouse -

Additional
Requirements

Software Manufacturer Vendor Part No. Comment
none

Protocol

Type Supported Baud Rates Data Bits Stop Bits Parity Error Checking Hand Shaking Comment
Communication Network IMPACC System Communications Protocol Selectable from 300 to 38400 - - - - - -

Supported
Data Types

Data Type Comment
ASCII -
Digital -
Float 24-bit floating point
Long -
Signed -
Unsigned -

Supported
Memory Types

Device Memory Type Comment
none

Commands

Device Command Description Uses
none

Signal
Conditionings

Signal Type Description Comment Typical Gain Convergance Range
12AL 12 Bit Binary Scaled to EGUs - Alarming on out of range Ignores the most significant 4 bits (nibble) - 0 - 4095
12BN 12 Bit Binary Scaled to EGUs- No Alarming on out of range Ignores the most significant 4 bits (nibble) - 0 - 4095
15AL 15 Bit Binary Scaled to EGUs - Alarming on out of range Ignores the most significant bit. - 0 - 32767
15BN 15 Bit Binary Scaled to EGUs - No Alarming on out of range Ignores the most significant bit. - 0 - 32767
3BCD 3 Digit Binary Coded Decimal Scaled to EGU range in the block. Alarming on out of range. Ignores most significant 4 bits (nibble). - 0 - 999
4BCD 4 Digit Binary Coded Decimal Scaled to EGU range in the block. Alarming on out of range. - 0 - 9999
NONE Returns raw value Ignores EGU range in the block. No alarming on out of range. - No Scaling.
SGNLIN Signed Linear Scaled to EGU range in the block. No alarming on out of range. - -32768 - +32767
UNSGNLIN Unsigned Linear Scaled to EGU range in the block. No alarming on out of range. - 0 - 65535

Miscellaneous
Info

Relevant Notes
4/4/01: NOT W2K COMPATIBLE DUE TO 3RD PARTY CONSTRAINTS.

History

Revision History
Reason for 6.03 Release on 6/8/98:
* Added support for Data Plus device.

Reason for 6.03b Release on 12/10/98:
* Corrected SA Energy Reset.

Reason for 6.03c Release on 08/17/2005:
* Updated to reflect GE Fanuc branding.


Details
ID: DG270
Category: I/O Drivers
Last Updated: 03/29/10
Date Created: 04/24/00
Status: Published
Attachments: Yes
Language: English


 


Feedback

The feedback portlet allows users to rate content and share these cumulative ratings with other users.
Overall Rating: 3.5 (2 responses)
Rate this content record (1=lowest, 5=highest)
5
4
3
2
1
Comment


Note:  If your firewall blocks ZIPS and EXEs, simply right-click and select SAVE TARGET AS and change the extension to something like "XIP".  Once downloaded change the extension back to its original one.

All drivers produced by vendors other than GE ("3rd Party Drivers") are provided by GE "as is" and without warranty of any kind unless the vendor extends a pass-through warranty to the end user.  Support for 3rd Party Drivers is provided by the driver's vendor.